Storm Damage Cleanup

Visible staining is usually smaller than the wet area. Technicians map it with a moisture meter and thermal imaging, then compare readings against a dry standard elsewhere in the same building — the restoration standard, ANSI/IICRC S500, works from that comparison rather than from how a surface looks or feels. Water trapped behind cabinets and under flooring shows up in the readings before it shows on the wall.

Three to five days is typical once air movers and dehumidifiers are running, though every loss is different and yours may need more time or less. The equipment stays until daily moisture readings match a dry standard in the same building, which is how ANSI/IICRC S500 defines dry rather than by a fixed count of days. Any rebuilding — flooring, drywall, paint — is a separate stretch of time after that and depends on what came out.

Standing water removal is the first thing crews do — submersible pumps for depth, then truck-mounted and portable extraction to pull what the pumps cannot reach, followed by drying equipment. Before extraction starts, the water gets categorized 1 through 3 under ANSI/IICRC S500, because clean supply water, used water and sewage are handled differently. The phone is answered around the clock, and you will get an honest arrival window for your address on the call.

Drying runs on air movers paired with low-grain refrigerant dehumidifiers, sized to the room's volume and the Class of loss the way ANSI/IICRC S500 lays out. Where material is contaminated or disturbed, HEPA vacuums and HEPA-filtered air scrubbers capture 99.97 percent of particles at 0.3 microns. Antimicrobial treatment is applied when the water category or the affected material calls for it, which depends on the specific loss rather than being routine.

Inspection first: the water is traced to its source, categorized 1 through 3 and the Class of loss is set, which is what ANSI/IICRC S500 bases the drying plan on. Then extraction, removal of material that cannot be dried, and placement of drying equipment with readings taken and logged daily until they match a dry standard elsewhere in the building. Repairs follow. What comes out, and how much, varies with the specific loss.

It depends on the water category and how long the material stayed wet, and that call is made from meter readings rather than appearance. Under ANSI/IICRC S500, carpet wet with clean Category 1 water can often be dried in place with the pad replaced, while Category 3 carpet and pad come out. Hardwood is sometimes dried with specialty mat systems; laminate rarely survives. Those are the typical outcomes; which one applies to your floor turns on the specifics.

Household fans move surface air but do not pull moisture out of the structure, so water inside wall cavities and under flooring keeps evaporating after the surface feels dry. That matters on a clock: EPA guidance is that wet material dried in the first 24 to 48 hours will in most cases not grow mold. A small clean-water spill caught immediately is often manageable; anything that soaked into walls, insulation or subfloor is not.

Identifying and stopping the source comes before drying — ANSI/IICRC S500 treats an unresolved source as a reason not to begin, since a structure still taking on water cannot be dried. The source also sets the water category, 1 through 3, which decides how wet material is handled. Moisture meters, thermal imaging and the shape of the wet area usually locate it, though some sources sit behind a pressurized line or roof assembly and need a plumber or roofer to open and test.

Yes — a crawl space dries like any other contained space: standing water pumped out, saturated insulation and vapor barrier pulled where they are holding moisture, then dehumidification until the framing reads at a dry standard. Water that has touched ground soil is Category 3 under ANSI/IICRC S500, so the material handling is stricter than a clean supply leak. Whether sealing or encapsulation afterward is in scope varies by office, so ask on the call.

Restoration work removes the water and dries the structure; keeping it out is a repair to whatever let it in, and that is a separate conversation. The inspection documents the entry point, which is what any fix has to follow. Exterior water usually traces to grading, gutters or flashing — the International Residential Code asks for the ground to fall six inches across the first ten feet out from the foundation. Which repairs are in scope depends on the property.

Time matters more than volume. EPA guidance is that wet material dried in the first 24 to 48 hours will in most cases not grow mold, and past that window the question changes from drying to assessing what has already grown — remediation then follows IICRC S520 rather than S500. Wood decay needs sustained moisture, generally above about twenty percent content, so a short soak and a week of standing water are different problems.

Often it can be dried in place. With clean Category 1 water, the baseboard comes off and the wall cavity is dried through small holes behind it, which leaves the wall intact. When the water was contaminated or the paper facing has lost strength, ANSI/IICRC S500 calls for removal, and the cut is usually made 12 to 24 inches above the wet line so the replacement lands on framing. The readings decide which applies.

ANSI/IICRC S500 sorts water into three categories: 1 is clean supply water, 2 is used water such as dishwasher or washing machine discharge, and 3 is grossly contaminated, including sewage and water that has touched ground soil. Clean water does not stay clean as it sits in building materials. The EPA and CDC describe mold and sewage exposure as a health concern, particularly for children, older adults and anyone with asthma. Containment and antimicrobial treatment apply at 2 and 3, depending on the loss.